How often synthetic oil change is made

The oil makes your car run better with respect to the engine, transmission and engine parts. Is the lubricating fluid that allows all parties to continue working without damage? Given technology, synthetic oil has been developed with better results and a longer life before needing changes in the fluid. In some cases it may take longer than mineral oil (traditional oil based), but in other cases, the rate of change is the same.

Why use synthetic?

Well-maintained vehicles have regularly been able to make up to 200,000 miles (321,868 kilometers) of travel, many of which have been converted into synthetic oil to prolong performance. So the product has proven to keep old cars running history. Given that older engines work with worn parts, lubrication becomes even more critical to protect these components.

Why does the synthetic more and requires less changes

The petroleum-based oil has a tendency to degrade under normal use of the engine. Over time it gets very hot and reaches a gaseous state, so it is useless for purposes of lubrication. Instead, the engine burning the residue is commonly known as carbon accumulation or burned. When the oil, some of it is washed adheres to engine parts, reducing yield. Frequently it needed oil changes to avoid this problem (every 3000-5000 miles; or 4828-8046 kilometers). The durability of the synthetic oil in the engine temperature it makes it a product of better performance because the synthetic still remains in liquid form, and usable. This temperature tolerance means that the oil can remain in the engine and can last as long as 7,000 miles (11,265 kilometers) before changing it.

Frequency of change

Most of the oils put guarantees a maximum length of mileage before a change 7,500 miles or 12,000 kilometers (many cars are closer to 5000 miles or 8,000 kilometers, even with better engines today). Because of the heat tolerance properties of synthetic oil 7,500 miles (12,000 km) are not a problem. That said, the frequency of oil change is a personal and financial decision.

Save money

You get a longer mileage with a synthetic oil, but you pay more per bottle because the price is usually more expensive. So you save money economically. Other reasons for the synthetic oil have nothing to do with the frequency, as some owners will partially synthetic oil put their cars.

Be careful when changing the oil types

If you are changing the oil frequently to extend the shelf life is not as simple as changing a new synthetic oil with an old mineral oil. You need to clean the system even after it is drained to confirm that no mixture is not formed. After washing, the first oil change should be around 2,000 to 3,000 miles (3218-4828 km) and other changes to get rid of waste from the final mixture.

How to change the oil at a Hyundai Tucson

The oil from the truck Hyundai Tucson works by lubricating the internal components of the engine to avoid jamming. The manufacturer recommends changing the oil every 3,000 to 5,000 miles, depending on the conditions in which you drive. A limit of 10,000 miles or more between oil changes is hardly acceptable, since oil breaks down over time due to heat generated inside the engine. While the oil helps to control the friction of internal components, and thus the heat output of it is inevitable. So, this heat slowly degrade the oil.

  1. Lift the front of the Tucson to cricket. You must place it under the wheel axle and lift the vehicle. Go underneath the vehicle and place the drip pan beneath the oil just oil valve.
  2. Make the cap to the oil valve, so it can drain out.
  3. Remove the oil filter. It is located directly on the oil valve and screwed to the motor housing. Turn the filter clockwise to remove it.
  4. Replace the plug once the oil has been drained.
  5. Place a small amount of new oil on the rubber seal of the new oil filter. Then install the new oil filter.
  6. Open the valve cover oil and place four liters of new oil. To check the oil level, take the dipstick and wipe it, then take it out again and reinstall. The oil level should be between the upper and lower marks on the dipstick. If this is not the case, you have to keep adding more oil until it comes to brands. Tighten the valve cap when finished.
  7. Remove the drip pan below the vehicle and the truck to the ground floor.

How to change the oil to a Ford 4.0 SOHC

It is advisable to change the oil and filter in your car every 3,000 to 5,000 miles (4828.03 to 8046.72 km), to remove any contaminants in the engine and keep it running smoothly. If Ford 4.0l SOHC engine found in many Ford Explorers, this is especially important, because the engine does not have a good record of reliability. In this case, the vehicle used is a 2002 Ford Explorer; however, the process is similar for other Ford vehicles equipped with the 4.0L SOHC engine.

  1. Lift the front of the vehicle using the jack and place it in the supports. Make sure the vehicle remains firmly under the crawl before.
  2. Place the drain pan under the engine oil pan and drain plug located. Unscrew the plug using the ratchet 3/8-inch (0.08 m) and tubes, allow the oil to drain into the tray. Once the oil has been drained from the engine, placed drain plug using the ratchet.
  3. Move the drain pan under the oil filter and use the oil filter wrench to remove the engine oil. The engine oil spilled at this point, so make sure to be careful as you lower the filter. Place your mouth filter down to within the oil to drain into the tray too.
  4. Open the container and filter replacement filter filled with all the 5W-30 oil that will contain. Enter your finger in the oil and move it around the rubber seal on the outside of the filter –this solid– create a seal. Then install the oil filter on the engine, squeezing your hand, without using tools.
  5. Lower the vehicle to the ground using the jack. Pop the hood and flip open the oil valve cover, using your hand. Pour remaining five liters of oil in the engine, reinstall the oil plug. Start the engine and let it run for five minutes to circulate the oil.

Tips & Warnings

  • No problem if you change the oil when the engine is hot, this allows the oil to flow more easily. If you do this, be sure to use protective arms, eyes and hands to avoid burns.

Changing the oil in your car in seven steps

You have to take into account that the oil change is one of the most important things you can do for the welfare of your car, as it helps to better engine performance and allows it to behave smoothly and last longer.

If you want to save a few euros you can change your own oil in your car.

First of all you must know that the old oil clogs the critical parts of your vehicle and could eventually cause a major engine failure, the repair could cost a lot of money. It is definitely one of the keys to car maintenance.

The first thing is to check the car manual to see how often you have to change the oil. Most often it oscillates depending on the model and brand between 4500-9000 kilometers. It is important not be in that range, since the oil is too viscous and would not fulfill its function lubrication.

What I need?

  • Bottle of oil (in this article we explain how to choose the best oil for your car).
  • Oil filter.
  • Magnetized screw for casing (optional).
  • Wrench or English.
  • Funnel

The steps you have to follow to change the oil are:

Precautions

Do not change the oil after using the car because the oil temperature can be very dangerous. The car oil change is best tempered so you can start the car and 5 minutes after the operation can begin.

Raise the car

So you can change your oil is necessary to raise the car so the easiest thing is to put a couple of portable ramps on a raised surface. It is very important to set the parking brake, stop the engine and leave the car at first. For your safety, place a wedge brake on the rear wheels.

Locate the screw crankcase

The next step once you secures the car is secured and stable is slide underneath the car and locate the oil drain plug on the engine. Check the manual of your car and know where your model lies in the drain plug, then place the oil catcher just below.

Unscrews the screw

Cerci Onate the engine is not hot, then loosen the plug with a wrench, or failing that, with a spanner until you can remove by hand, and do not panic with the amount of oil that will flow out of the crankcase.

Change the filter

oil filter car Then you get to change the oil filter so goes the hood, look at the car to locate manually, take the new filter and lubricate the rubber seal with a thin layer of oil to help protect it.

Fill the engine with oil

Now comes the easy part and that is to fill the oil tank located on top of the engine. Confirmed in the operating instructions and the capacity of the oil with the help of a funnel, pour the oil in the engine, but not all at once. Slowly and always checking the oil level.

Car oil dipstick to measure the level, locates the rod which is housed in the engine, usually of yellow color. It should be cleaned and re-enter to know where exactly level mark.

Check plugs

Make sure you’ve closed all plugs and check for anything drip under the car. Remember that the used oil is highly toxic to the environment so we recommend that you take it to a workshop for recycling.

Other tips

We recommend the use of a wrench instead of a wrench. You may use the latter to damage the screw and then cannot put, or worse, remove it.

Magnetic plug carter it would be interesting, at this point incorporating a magnetized screw. In the lower area of the engine waste accumulate. If they circulate through the engine, depending on the size of the metal chips, it could cause serious problems. This sump magnetic plug the trap and not allow them to move through the circuits, so it will keep oil cleaner and your engine will always be in perfect condition

How to make your own oil change ramps

Ramps to change oil are great for accelerating the process of changing your oil when you practice keeping your regular car. Instead of taking the cat and support, you can simply move the wheels front of your vehicle on the ramps to lift the front end. While most sellers of auto parts and tools selling a variety of ramps, you can make your own ramp for little or no money and about 10 minutes of effort. Anyone who has hand tools can make your own ramps to quickly and easily change oil.

  1. A table placed 76 cm (30 inches) long of 5×30 (cm) flat on the ground. Supports a table of 61 cm (24 inches) long of 5×30 (cm) above it with the rear ends of two aligned tables.
  2. 8cm sticks a nail through a table of 61 cm (24 inches) to 76 cm (30 inches), using the hammer. The first nail should be approximately 3 cm inside from the front edge of the table of 61 cm (24 in) and 3 cm in from the right edge. Pin a second nail through the back left corner of the table of 61cm (24 inches) to 76 cm (30 inches), using the hammer.
  3. A table placed 46 cm (18 inches) in the ground. Supports a table of 30 cm (12 inches) above it with the rear ends of two aligned tables.
  4. 8cm sticks a nail through a table of 30 cm (12 inches) to 46 cm (12 inches), using the hammer. The first nail should be approximately 3 cm inside from the front edge of the table of 30 cm (12 in) and 3 cm in from the right edge. Pin a second nail through the left rear corner of the table of 30 cm (12 inches) to 46 cm (18 inches), using the hammer.
  5. Supports the joined tables of 30 cm and 46 cm above the 61cm and 76cm with the rear edges of the four aligned tables. This should create a ladder effect with the front edges of the boards. Repeat steps 1 to 5 with the remaining boards and nails to create the second ramp.

Changing the oil in a Honda Accord

The Honda Accord usually has few problems during his life useful, and the maintenance regularly helps it last longer. The process to change the oil in a Honda Accord is simple, and you can easily find replacement filters in an auto shop. Here’s how to change the oil in a Honda Accord from 1996 to 2000.

  1. Raise your Honda Accord using a car jack. Then let it rest on the supports. If you do not have the supports, you can upload it to a ramp using a bracket to block the front wheels.
  2. Pop the hood and then remove the oil filler cap and dipstick. They can be found located on either side of the engine. The oil filler is usually above the rod.
  3. Have on hand your oil drip tray, the key filter, drain plug wrench, cleaning cloths, washer and new oil filter. Honda models require a 17 mm wrench to remove the drain plug. Slide under the car and locate the oil drain plug and filter. The cap is usually in the lower rear of the engine with the filter on the lower front section.
  4. Remove the drain plug with a 17 mm wrench. Get it out quickly and let the oil leak in the drip tray fall for about 10-15 minutes. Clean excess oil and replace the washer and the drain plug.
  5. Unscrew the old oil filter with the filter wrench and empty the oil in the drip tray. Place the filter in a plastic bag to get rid of him.
  6. Inspect the threads and make sure the rubber seal is not attached to the engine block. Cover the board with a little oil and replace the oil filter.
  7. Recharge your Accord with fresh oil and replace the rod. Accord models work better with a viscosity oil 5W-30 or 10W-30 depending on the temperature of your area. 5W is good for colder temperatures, while 10 W is good for very high temperatures. The Accord has approximately 4.5 quarts (4.5 liters) of oil.
  8. Turn on your car and let it run for a minute to create oil pressure. Check the dipstick. If the oil line is not complete, add a little more. Close the lid and lower the car.

Changing the oil in a Dodge Caliber

Change the oil in your Dodge Caliber regularly will help to prolong the life of the engine and maintain high performance. When you buy the oil and filter replacement, double check your owner’s manual to be sure you will use an acceptable oil. Until 2010, Dodge recommends that oil replacement for the Dodge Caliber material meets the standards Chrysler MS-6395.

  1. Has all the tools and accessories you need, before changing the oil. Once the oil has drained you cannot start the car until the oil change is over.
  2. Find a safe place to perform an oil change. A location that is level with a firm surface would be ideal. Make sure there is sufficient space to work around the car.
  3. Activate the parking brake of the car. Make sure you have enough room to work under the vehicle.
  4. Place the supports for the car to be supported flat on the floor and grip the frame of the car. You may need to raise or lower the car for proper contact between the support and the frame.
  5. Locate the oil drain plug at the bottom of the engine.
  6. Place a container beneath the drain. Make sure the container is large enough to hold all the oil in the engine.
  7. Remove the drain plug with adjustable wrench. Let the oil drain until the flow stops.
  8. Replace the plug and tighten it with the wrench.
  9. Remove the container of used oil and place under the oil filter.
  10. Remove the old filter with the oil filter wrench. This filter is full of oil, so carefully place it in the container of used oil and leave it to be emptied.
  11. Place the new filter. And adjusted by hand clockwise. With filter wrench approximately 1/4 I set it back.
  12. Remove the oil container, tools, accessories and brackets used to jack under the car.
  13. Lower the car to the ground with the jack.
  14. Pop the hood of the car and locate the oil cap placed. It is located in the valve cover. Remove the oil cap.
  15. Check your owner’s manual to determine the exact amount of oil that needs your Dodge Caliber. Add the new oil using the funnel.
  16. Check the engine oil level. Make sure the oil level is within the recommended area.
  17. Discard the used oil and filter according to local laws.

How to reset the oil life in GM vehicles

General Motors has an indicator that informs the driver when the oil in the engine must be replaced. The indicator on the life span of the oil used factors such as style of driving, mileage accumulated and weather conditions. An indicator such as a warning light on the instrument panel or a warning screen on the driver information center will let the driver know the time when the oil should be changed. The proper functioning of the warning system of the oil life requires the system to reboot manually after each change it.

  1. The General Motors vehicles used this procedure for 2006 and newer. Turn the ignition to the ON position (turn) without starting the vehicle. Hold the ENTER button (enter) the driver information center for one second, while the message of the life of the oil is shown. Turn the key to OFF (off) once the message is displayed. Turn the car to check the oil change message is restored.
  2. General Motors vehicles used this procedure for 2005 and earlier. Turn the ignition to the ON position (turn) without starting the vehicle. Press and release the accelerator pedal completely three times in less than five seconds. Make sure the CHG OIL SOON message flashes twice. Turn the ignition key to the OFF position (off). Turn the vehicle to make sure the CHG OIL SOON message no longer appears. For some 1998-2002 vehicles of General Motors, press and hold the odometer button for 12 seconds until the message goes out oil change.
  3. Use this procedure to General Motors vehicles with a reset button: Turn the ignition to the ON position (on) without starting the vehicle. Hold the reset button on the end of the dashboard near the fuse box for five seconds. Turn the vehicle to make sure the oil change light has gone out.

Tips & Warnings

  • Consult the owner’s manual for specific information on restoring your system oil life.
  • Check the oil level in all fuel stations. The system oil life does not indicate when the oil level is low.

Changing the oil and filter marine engine

Like any abnormal sound in the engine of a car arouses the attention of the driver, a marine engine requires the full attention of his boss to give his all. Servicing the engine of our pleasure boat helps us to know all the particulars of the ship and part of the duties of a good pattern. All captain knows his boat like the back of his hand. A reason for this in navegar.com we have been publishing some tips for boat maintenance and boat engine. In a previous post we saw the maintenance and change the water filter decanter. Now I play two key elements of any marine engine: oil lubrication and oil filter.

Oil selection

The choice of oil for the engine of our boat must not involve more difficulty in the manual of the machine to meet the manufacturer’s recommendation. In this respect it is not advisable to be brave. The voice of the manufacturer may or may not respond to subjective criteria regarding the brand, but always respond to technical criteria regarding the graduation of the oil.

The marine engine oil can be monogramed or multigame. The difference is that the monogramed oil has a very specific range of viscosity where the lubricant maintains its properties. Most commonly the multigame oil, based on the SAE (Society of Automotive Engineers), or Society of Automotive Engineers in the Spanish translation classification.

The viscosity of the lubricating oil of marine engines and influences their behavior is a function of temperature. A marked oil SAE 15W-40, means that it has a viscosity grade 40, which is not intended for use at 40 ° C. While the letter W indicates the viscosity at freezing temperatures.

How and when to change the oil

The oil change marine engine should meet the criteria of the engine manufacturer. However, the oil change must be forward when the engine runs at high speed for a long time and can be extended when normally navigate at low revs. Manufacturer criterion refers to a rate of operation next cruise ship.

To make the change engine oil must have a suction pump. The hose is provided that is inserted through the hole to house the dipstick level and proceed to emptying. All motors are advised that the machine has an average temperature for the fluid to flow more easily.

The extraction of oil used is the opportunity to examine the internal state of the engine. The presence of metallic waste is the alarm that parts that do not perform proper motion, being subjected to friction.

Note that the oil from the ship machine are subject to MARPOL regulations, and therefore must be deposited in the agreed locations, as discussed when talking about garbage and waste in the sea .

Changing the oil filter

Once emptied all, or almost, the lubricating oil it is time to proceed to change the oil filter. However, the filter change can alternate every two oil changes, provided a similar oil is used and have not appreciated metallic debris in dirty oil. The oil filter retains its panel’s metal splinters arising engine operation. To remove it is usually necessary to have an adjustable wrench to clamp the work piece diameter. Not so for the new place, it will be sufficient hand strength so that it is firmly in place.

The supply of oil filters for marine engines is broad. From block filters in which all elements are integrated into one piece, the filter cartridge where it is only necessary to change the removable cartridge.

The position of the filter in the engine is usually such that it allows full extract oil without causing the spill in the hold, which would result in the bottom cleaned. Also, this position allows the filter clean place full of new oil, avoiding gaps that may occur in the circuit.

It placed the filter, which is never to tighten with wrench for installation, proceed to complete the filling of the crankcase with new oil. Always having the caution that the level is between the minimum and maximum acceptable for the machine. Both excess and defect mechanical oil have dire consequences. The next step involves the launch engine for a few seconds, stop and check the oil level. It is preferable to rectify because we have fallen short, and we have passed.

Changing the oil in a Honda Accord

The Honda Accord usually has few problems during his life useful, and the maintenance regularly helps it last longer. The process to change the oil in a Honda Accord is simple, and you can easily find replacement filters in an auto shop. Here’s how to change the oil in a Honda Accord from 1996 to 2000.

  1. Raise your Honda Accord using a car jack. Then let it rest on the supports. If you do not have the supports, you can upload it to a ramp using a bracket to block the front wheels.
  2. Pop the hood and then remove the oil filler cap and dipstick. They can be found located on either side of the engine. The oil filler is usually above the rod.
  3. Have on hand your oil drip tray, the key filter, drain plug wrench, cleaning cloths, washer and new oil filter. Honda models require a 17 mm wrench to remove the drain plug. Slide under the car and locate the oil drain plug and filter. The cap is usually in the lower rear of the engine with the filter on the lower front section.
  4. Remove the drain plug with a 17 mm wrench. Get it out quickly and let the oil leak in the drip tray fall for about 10-15 minutes. Clean excess oil and replace the washer and the drain plug.
  5. Unscrew the old oil filter with the filter wrench and empty the oil in the drip tray. Place the filter in a plastic bag to get rid of him.
  6. Inspect the threads and make sure the rubber seal is not attached to the engine block. Cover the board with a little oil and replace the oil filter.
  7. Recharge your Accord with fresh oil and replace the rod. Accord models work better with a viscosity oil 5W-30 or 10W-30 depending on the temperature of your area. 5W is good for colder temperatures, while 10 W is good for very high temperatures. The Accord has approximately 4.5 quarts (4.5 liters) of oil.
  8. Turn on your car and let it run for a minute to create oil pressure. Check the dipstick. If the oil line is not complete, add a little more. Close the lid and lower the car.